Vehicles
Sections
139 not categorized PORSCHE 996 TURBO A ARMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1978-82 (includes uncategorized and accessory items) BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection BES98215000S2 The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$2,816.00
Make a selection FSPOR992TVLV Treat your 992 turbo to the finest cat-back exhaust solution on the market. This valveed exhaust system is plug-and-play with the factory pse system so you can turn pse off for quiet highway cruising and turn pse on for ripping twin turbo sports car sound!
$5,245.95
Make a selection FVD721T223 Synchro removal tool kit needed for the proper removal of synchro rings from the gear. For Porsche 930 turbo's w/4speed 76-88 3rd, 4th gears.
$223.30
Make a selection 93033229700EQ High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 4 necessary per car (2 per axle). Please note: this only fits 930 turbo models with the 4 speed transmission # 930.34/36 and the 1984 911 wide body models with the 5 speed transmission # 915.69 and 915.70.
$5.50
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,194.50
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$4,312.00
Make a selection 99312301452ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turbocharger. After receiving y...(choose a part on the right to read more)
$2,194.50
Make a selection F9664120202TT This is for the 996 turbo model with logo in center tach. The differences are day and night! Gauge faces are one of the most visible and frequently looked at components in your Porsche. Why skimp on quality? Gauge faces should have clearly visible markings and be easy to read with and without back lighting. Replacement faces should offer similar qualities, but many gauge faces on the market don't quite make the grade. FVD gauge faces are different. What makes them different you ask? See for yourself. In the below pictures you will see that the tiptronic is an FVD gauge face and the 6 speed gauge face is the competitions. The daytime difference (the competition): darker, more yellow appearance raised orange war...(choose a part on the right to read more)
$493.90
Make a selection 22011099706 The 997 turbo ipd "y" pipe was built for the more demanding turbo performance customer. The factory y pipe becomes restrictive when adding substantial power gains. The ipd "y" pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory y pipe delivering the additional power needed to raise the performance bar on any turbo. The ipd "y" y pipe is designed to be a direct replacement of the factory OEM y pipe. There are no modifications or fabrication required for installing the ipd y pipe. This is an easy and straight forward r & r (remove and reinstall) bolt on upgrade. Note: contains everything nec...(choose a part on the right to read more)
$1,094.50
Make a selection FVD721883081 High quality, German made brake bleeder and vacuum pump kit. Ideal for use on brakes, clutches, hvac, bleeding the fuel system or testing vacuum on a turbocharged system. Vacuum can be tested up to 0.9 bar and pressure up to 4 bar. The kit is complete with a variety of hose ends for various connections. Sold individually. General FitmentACCESSORY
From $246.40
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FVD351997GT2CS2 This kit convert's the 997 turbo GT2's / 997gt3 rs pccb rotors to 997 GT3 cup car steel rotors with green cup car pads ( for cars with central lock only ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 8 x cup brake pads (racing green) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$7,260.00
Make a selection FVD11104001 These headers are meant to replace the original 993 GT2 r (993 111 039 83) headers that are no longer available. They will reduce turbo lag and add horsepower and torque. Made of t316 stainless. Primaries are 42mm (1.65 ). Merge into a 50mm (2 ) motorsports collector. Manufactured by m&m exhaust in Germany.
$1,835.90
Make a selection FVD123025ATK K24/26 exchange turbo (only OEM k24 exchange accepted) (up to 700 hp) power is focused on mid and top range rpm's. Facts: - modified compressor housing and backing plate - modified & lightened high flow compressor wheels. - remanufactured by kkk / borg warner certified technicians - free software update for those already running FVD software. FVD brombachers 996 k24/26 race turbos are new units created for those who are looking for ultimate in performance. Power is focused in the mid and top rpm range while keeping turbo lag low. They are completely bolt on and do not require custom headers or special modifications. The factory OEM turbocharger compressor housing is re-profiled and the compressor backing plate...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123042ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection FVD351997TTCS1 This kit convert's the 997 turbo pccb rotors to steel rotors with yellow pagid pads.( only 5-hole, not central lock ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 2 x set ( front and rear ) brake pad set (pagid yellow - rs29 ) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$5,871.80
Make a selection FVD123048ATK FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$2,634.50
Make a selection FVD123048 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,413.00
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection FVD20799601 Scavenging and aeration in the oil pan have been identified as a problem in 996 and Boxster models experiencing high g-forces on the racetrack. This oil pan spacer provides a simple solution. This spacer increases sump capacity by half a liter, providing more reserve to ward off starvation. Thisoil pan spacer clears all factory options including the rear skid plate. Added oil capacities as well as increased oil pan surface area increase oil cooling and engine performance. *oil pan and sump baffle are OEM parts and do not need to be purchased material: 6061 t6 aluminum alloy finish: clear anodized weight: n/a models: Boxster, Boxster s, and 996 models (excludes GT3 and turbocharged models) installation: for best...(choose a part on the right to read more)
$283.80
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |